Technical Information Marking Spray
MoTip Marking Spray offers excellent coverage and intense brightness for long-lasting and resilient markings in car parks, storage areas and fork lift truck routes
For use on stone, concrete, asphalt and metal.
The 360° valve facilitates perfect all-round marking in every direction.
It is available in white, yellow, red and grey.
Use marking cart for exact mark linings.
Physical and chemical data
- Basis of the binder: acryl resin
- Colour: white, yellow, red, grey
Depending on consistence and color of the ground:
600 ml are sufficient for approx. 60 m
- Drying time (at 20°C, 50% relative air humidity):
Cured: after 16 hours
- Storage stability:
10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
aerosol cans, maximum nominal volume 600 ml
Environment and labelling
Environmentally compatible: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse".
Only for DE: In order to ensure a high reuse and recycling rate, the legislator requires, in accordance with §15 - VerpackG, Paragraph 1, the return of transport, sales or outer packaging, alternatively, however, deviating agreements can also be made.
Labelling: All products of European Aerosols comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,
- The surface should be clean, dry and free of grease.
- Bring the can to room temperature.
- Operating temperature 15 to 25°C.
- Shake for 2 minutes before use.
- Test on inconspicuous area.
- Apply required width of spray.
- For optimum results, we recommend a speed of 1 metre pro 4 to 5 seconds.
- After use, hold upright and spray empty to clean the valve.
Tips for spray painting
Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.
The aerosol can should have room temperature.
Temperature should range between +10°C and +25°C, max. air humidity 60 %.
Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!
|Bodenmarkierung gelb 600||600 ml||000223|
|Bodenmarkierung rot 600||600 ml||000221|
|Bodenmarkierung weiß 600||600 ml||000222|
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.
For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.
As of: May 10, 2010
This release replaces all eventually earlier issued versions.