Technical Information pre-fill System water-based
Quality and properties
- A spray can pre-filled with propellants and specific additives. The water-based coat is transferred into the can by a filling device, producing a ready-to-use end product
- High coverage
- Simple, time-saving application
- Excellent atomisation
- Light blending
- Suitable for filling with all ColorMatic filling machines
- The dealer adds the desired coat colour and is, therefore, liable for the final product
Ideal for spot repairs
Physical and chemical data
- Colour: depending on filling
- Smell: solvent
- Degree of gloss: matt. It is necessary to re-coat wb basecoats with 2K clear coat. After the varnishing with clear coat the basecoat is featured with an excellent weather- and chemical resistance and a everlasting gloss.
- Efficiency:
Depending of consistence and colour of the substrate - Substrate:
Depending on the colour of the substrate apply Primer Filler HG1 - HG8, ColorMatic Plastic Primer, Art.-Nr. 856 563, ColorMatic 1K Primer for Alu, art.-no. 190278, ColorMatic 1K Primer for Zinc, art.-no. 190285, ColorMatic 1K Epoxy Primer, art.-no. 174414, ColorMatic 1K Filler, art.-no. 856556 + 874987, ColorMatic 2K Hi-Speed Primer Filler, art.no. 195327 - Drying (at 20°C, 50% relative air humidity): 20 - 30 min.
The drying time depends on the ambient temperature, the air humidity, the applied paint thickness and the filled type of paint - Storage: empty cans: 5 years
Filled cans: between 4 and 14 days depending on colours
If appropriate storage provided (=10°-25°C, relative air humidity max. 60%) - Size:
Aerosol cans, maximum nominal volume 400 ml and 15 ml, filling quantity 100ml for art.no. 202117; filling quantity 30 ml for art.no. 201271 - VOC-value:
Art.Nr. 202117: 216 g
Art.Nr. 201271: 81 g
Order information
- Pre-treat undercoat with a basecoat as usual and clean with ColorMatic silicone cleaner no. 174469
- Shake can vigorously for 2 minutes
- Carry out spray tests
- Base cats must be coated with ColorMatic 2K hi-speed clear coat gloss no. 187216, or satin no. 231650
- Surface can be re-coated after 30 min drying-time
2-3 full coats, 50µ - Leave to dry for 2 minutes between coats
- For professional use only
- Wear an appropriate respirator (recommended type A2/P3)
Environment and labelling
Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".
Marking/Labelling: All products made by European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.
As of August 1, 2013
This release replaces all eventually earlier issued versions
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.