Technisches Merkblatt Hitzefest-Spray

Technisches Merkblatt Hitzefest-Spray

Zur Ausbesserung von hitzebeanspruchten Untergründen wie Auspuffanlagen, Öfen und Grill usw. Kann ohne Vorbehandlung auf blanke Metallflächen gesprüht werden. Keine Grundierung erforderlich! Nur in matter Qualität erhältlich.

Qualität und Eigenschaften

  • Hochtemperaturbeständig bis 650°C
  • Hohe Deck- und Füllkraft
  • Ausgezeichnete Haftung
  • Guter Verlauf, glatte Oberfläche
  • Schnelltrocknend
  • Wetterbeständig
  • Nach dem Einbrennen beständig gegen Benzin, Chemikalien und Witterungseinflüsse

Physikalische und chemische Daten

  • Bindemittelbasis: Silikonharz
  • Farbe: schwarz, silber
  • Geruch: nach Lösemittel
  • Glanzgrad: im 60° Messwinkel nach DIN 67530
    matt: 5-10 GE
  • Ergiebigkeit:
    Je nach Beschaffenheit und Farbe des Untergrundes reichen
    400 ml für ca. 1,25 - 1,75 m²
  • Trocknung (bei 20°C, 50% relative Luftfeuchte):
    Staubtrocken: nach 5 bis 10 Minuten
    Klebefrei: nach 10 bis 15 Minuten
    Ausgehärtet: nach 30 bis 60 Minuten
    Die Trocknungszeit ist abhängig von der Umgebungstemperatur, der Luftfeuchtigkeit und der aufgetragenen Schichtstärke.
  • Temperaturbeständigkeit: bis 650°C
  • Haltbarkeit/Lagerung:
    10 Jahre bei sachgerechter Lagerung (=10°-25°C, relative Luftfeuchte von max. 60%)
    Sedimentationsverhalten: Nicht aufgetreten
  • Gebinde/Inhalt:
    Aerosoldosen, maximales Nennvolumen 400 ml

Environment and labelling

Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Instruction manuel

The most MoTip spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!

Untergrundvorbehandlung:

  • Lose Altanstriche und Rost entfernen, danach anschleifen
  • Der Untergrund muß sauber, trocken und fettfrei sein.
  • Nicht grundieren! Beste Ergebnisse werden auf blankem Metall erzielt.


Lackieren:

  • Die Dose auf Raumtemperatur bringen.
  • Verarbeitungstemperatur 15 bis 25°C.
  • Nicht zu lackierende Flächen abkleben.
  • Vor Gebrauch Dose 2 Minuten schütteln.
  • Probesprühen und Lackverträglichkeit an unauffälliger Stelle prüfen.
  • Im Abstand von ca. 2 Minuten mehrere dünne Schichten aufsprühen.
  • Die Sprühentfernung sollte ca. 25-30 cm betragen.
  • Während des Gebrauches die Dose ab und zu schütteln.
  • Bei Raumtemperatur eine Stunde trocknen lassen.
  • Danach ca. 30 bis 60 Minuten erhitzen (160°C), damit die Lackschicht aushärtet.
  • Nach Gebrauch die Dose umkehren und das Ventil zur Reinigung leer sprühen.
  • Je dünner die Lackschicht, desto besser die Temperaturbeständigkeit.

Tips for spray painting

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

 

Bestellangaben

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

There are no prdocuts to show.

Anwendungsbeispiele

Technisches Merkblatt Hitzefest-Spray
Technisches Merkblatt Hitzefest-Spray

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.

Stand: 08. Juni 2010
Mit dieser Version werden alle evtl. früher erschienenen Versionen ungültig.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Hier kunt u gestileerde muurschilderingen in blad-patroon maken. De truc: de bladen worden niet geschilderd maar erop gespoten met stencil...

Meer lezen

Hier kunt u gestileerde muurschilderingen in blad-patroon maken. De truc: de bladen worden niet geschilderd maar erop gespoten met stencil...

Meer lezen