Technisches Merkblatt Frigoweiß
Physikalische und chemische Daten
- Bindemittelbasis: Alkydharz
- Farbe: Email-weiß
- Geruch: nach Lösemittel
- Glanzgrad: im 60° Messwinkel nach DIN 67530
glänzend: 80-85 GE - Ergiebigkeit:
Je nach Beschaffenheit und Farbe des Untergrundes reichen
400 ml für ca. 1,2 m² - Trocknung (bei 20°C, 50% relative Luftfeuchte):
Klebefrei: nach 4 Stunden
Durchgetrocknet: nach ca. 24 Stunden
Die Trocknungszeit ist abhängig von der Umgebungstemperatur, der Luftfeuchtigkeit und der aufgetragenen Schichtstärke. - Temperaturbeständigkeit: bis 80°C
- Haltbarkeit/Lagerung:
10 Jahre bei sachgerechter Lagerung (=10°-25°C, relative Luftfeuchte von max. 60%) - Gebinde/Inhalt:
Aerosoldosen mit maximalen Nennvolumen 400 ml
Environment and labelling
Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".
Marking/Labelling: All products made by European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.
Untergrundvorbehandlung:
- Lose Teile, Rost und Schmutz entfernen.
- Der Untergrund muß sauber, trocken und fettfrei sein.
- Die Schadstelle und einen kleinen Teil der umgebenden Flächen anschleifen.
- Schleifstaub entfernen.
Lackieren:
- Dose auf Raumtemperatur bringen.
- Verarbeitungstemperatur 15 bis 25°C.
- Vor Gebrauch Dose 2 Minuten kräftig schütteln.
- Probesprühen und Lackverträglichkeit an unauffälliger Stelle prüfen.
- Aus ca. 25 cm Abstand im Kreuzgang mehrere dünne Schichten aufsprühen.
- Auch nach der Durchtrocknung nicht mit Acryllack oder Nitro-Kombi-Lack übersprühen!
Tips for spray painting
Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.
The aerosol can should have room temperature.
Temperature should range between +10°C and +25°C, max. air humidity 60 %.
Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.
Stand: 12. Mai 2010
Mit dieser Version werden alle evtl. früher erschienenen Versionen ungültig.